Sealed Concrete

Sealed concrete-Port St Lucie Concrete Contractor & Repair Services

Sealed Concrete

Sealed concrete-Port St Lucie Concrete Contractor & Repair Services

free quote-7-Port St Lucie Concrete Contractor & Repair Services

 

One of the best ways to make your concrete surfaces more resistant to the exposure of weather, deicing salts, abrasion, grease and even water is applying sealed concrete. These surfaces also bring the much-desired natural beauty to your concrete surfaces and are easy to clean. However, for the sealers to work this magic on your floors, you have to make sure that you apply it properly.

The best starting point is getting the right professionals to work on this task. One of the best examples of sealed concrete professionals in the region is Port St Lucie Concrete Contractor & Repair Services. You need the right preparation for the surface and use the correct application tools to create a significant impact on the final outcome.

In this section, I want to give you some tips for sealed concrete application [stamped concrete driveway port st lucie fl]. Make sure you follow the recommended specifications that the manufacturer provides depending in the brand of the sealer that you are using. The reason is that some of them may be different from the general guidelines that I am providing below. Here is a summary of the step by step guide of applying sealed concrete.

  1. Remove all the dust, dirt, stains, grease, and oil from the concrete surfaces
  2. Strip off any sealer that could be on the surface.
  • Use an etching solution to open up the concrete
  1. Either use a sprayer or roller to apply a thing coat of sealer
  2. Give the first layer of sealer enough time to dry
  3. Apply the second coat of sealer in the opposite direction
  • Alloy this sealer to dry fully and then you can drive or walk on the concrete surface.

 

When to Apply Sealed Concrete

It is important to apply a sealer on your concrete surfaces. However, give the new concrete enough time cure fully. It can be approximately 28 days or as per the recommendations of the manufacturer. In most cases, apply the sealers under dry conditions because applying sealers to concrete that is damp can cause loss of adhesion and haziness. The other important factor is the air temperature and should be above 50°F and for a minimum of 24 hours after applying the sealer. Allow the sealer to completely dry before you expose it to vehicle or foot traffic. The drying time before such an exposure can run for as long as three days.

free quote-7-Port St Lucie Concrete Contractor & Repair Services

 

Concrete Preparation for Sealing

It is extremely important to prepare your surfaces before you apply the sealer. Remove all the dust, dirt, stains, grease, and oils before making any application. The challenge with such debris is that it can block your sealer from adhering properly. Besides, if you are applying the sealer on a different brand sealer, the manufacturer may advice you to remove all the traces of the sealers you had used previously because the two products may not be compatible. Some of these manufacturers may tell you to etch the solution to get the best adhesion.

 

How to Apply Sealed Concrete

To get the best sealer thickness and coverage rate that will give you optimal performance, you need to use the right tools. There are two approaches to sealed concrete applications that include using the sprayer or roller. The method you choose depends on whether the sealer is water-based or solvent. It is good to refer to the specific guidelines of the manufacturer [concrete stamping company port st lucie] before you make a decision. 

Whether you are rolling or spraying the sealer, you need to aim for maximum coverage. The average rate of coverage is 250 to 300 square feet for one gallon. However, it all depends on the porosity of your concrete. The most important rule that you need to remember is that less is more. It is better to apply two thin coats as this will make sure that the sealer does not puddle or make uneven thick areas.

As you apply the second coat of the sealer, do it in a direction that is opposite of perpendicular to the initial coat. Port St Lucie Concrete Contractor & Repair Services will give you the best sealed concrete results. The company has well trained and highly skilled professionals for this task.

free quote-7-Port St Lucie Concrete Contractor & Repair Services

 

Here is a list of our services you can get at Port St Lucie Concrete Contractor & Repair Services:

1) Concrete Driveway Resurfacing

2) Concrete Driveways

3) Decorative Concrete

4) Driveway Repairs

5) Patio Concrete

6) Polished Concrete

7) Sealed Concrete

8) Stained Concrete

9) Stamped Concrete

Request for a free quote from our Concrete Contractor & Repair service company now!

We also service all cities throughout St. Lucie County! Below are a list of cities where we offer our Concrete Contractor & Repair Services:

  1. Fort Pierce
  2. Hobe Sound
  3. Palm City
  4. Stuart
  5. Vero Beach
  6. All cities in the St. Lucie County area. Just call and ask!

free quote-7-Port St Lucie Concrete Contractor & Repair Services